Ameer Ahmad
[email protected] Mobile no.- 0569857941
Career objective
Looking for a challenging position Electronics engineer/ICT/ LOW current engineer
in reputed organization with a view to use my wide experience for the benefit of the organization.
ETECHS(14-05-2025 to continue..) as Electronics technician
In SEC power Substation at GIS locations doing PM and CM of detector, Fire alarm controller systems, Wiring, following safety guidelines, making report, SLA, AUTOCAD 2018
C++, LTSPICE, LabVIEW, C++ programing, Soldering and troubleshooting electronic circuit. SIEMENS PADS software training for PCB designing, Oscilloscope, Waveform generator, Multimeter. Auto Cad 2018.
Trapeze group (21-05-2023 to 22-5-2025) as Electronic Field Service Technician
Fixing NVR, LED/ TFT, and using MxManagementCenter to fix Mobotix CCTV installed at BRT and Riyadh bus stops. Working on LIO and workstation. Writing work permit before going to stops to fix the issues. Doing PM and CM, Preparing service documents according agreement, SLA, stay updated according company standard, coordinate with other team to fix the issue. Maintenance 1 phase and 3 phase UPS located in data center. Well-versed in battery backup and emergency supply protocols. Working under pressure.
FLIR teledyne, METCO, RSTS (16-10-2019 to 09-03-2023) I was employee in TELEDYNE FLIR service center in Riyadh. I repair and troubleshoot the HRC cameras using MAPPING, COLLIMATER, TIMESTAMP, LEACKAGE TESTING, TEAMPRATURE TESTING methods etc. Working on FLIR SENSOR MANAGER 4.0/4.3.
Every day work on SCADA which was installed on LANCRUISER MILITARY CAR. This car was equipped with FLIR HRC/HRX ranger camera.
Zijan, Najran and Sharorah airport including preparing and installation of electrical panel, CCTV and radar installation, commissioning, mounting switch gear completed.
ICT supervisor at GACA/Alulah airport project, Commissioning, Installation, LV/MV switchgears, transformers, and UPS, the task of security devices like road blocker, cameras and access control system, installation of video wall. Commissioning Electrical work like MDB, electrical wire termination, ATS, GENERATION, TRANSFORMER installation, 3 phase UPS installation for data center.
Assigning IP addresses, installation and troubleshooting of CCTV like Axis. Configuring and termination Access control system (LENEL 2210, 1320, 1200 and 1100), installation of turnstile. Working on auto cad 2021 also reading and understanding diagram, FLIR radar installed.
I have good working knowledge with milestone and perspective VMS, finding recordings from MILESTONE. Working with ONGUARD 7.6, alarm monitoring, system administration to troubleshoot and find the status connected devices with Lenel. Not more but familiar with CNL Software and CAMELEON software for FLIR radar.
TRANSCORE (January 2018 to 3-9-2019)- as Traffic signal tech.
Configuring VDU/ vehicle detector, IP assigning to VDU, Working on PEEK CONTROLLER, CCTV installation, IP configuring and troubleshooting, Practical as well as theoretical knowledge of AC and DC volt, low voltage. Hands on experience on MULTIMETER, CRO, SIGNAL GENERATOR and electronics circuit repairing and Understanding of SG & SP drawing, Electrical or electronic repairs at existing traffic signalized intersections, Troubleshooting through component replacement, relays, load switch, flashers, surge suppressor, generator removing and installation on sites, Troubleshoots a traffic signal cabinet equipment, components and devices; such as traffic signal controllers, Load switch, flasher, MMU’s, LSU, vehicle detectors (video detectors), detector cards and racks, pedestrian crossing indicators, traffic signal indicators , pedestrian pushbutton. etc.
GENERAL ELECTRIC, Ebttikar Technology, ACS, Saudi Athel company Alhamrani Universal Company (02-11-2009 to 08-01-2018)-
SECURITY devices-
Configuring MARCH, ATV, REVO DVR, BOSCH Intrusion panel(9412gv3) wiring with door contact, smoke detector, motion detector, temperature detector and temper.
ATM machine-
• My job in this company was field service engineer for Diebold ATM machine.
• Working on Diebold Kiosk as well as ATM Machines.
• Fixing the BCRM & ECRM Module of Diebold ATM Machines.
• Cassettes contact pins setting for 500, 100, 50 Saudi Riyal.
• Trouble shooting and replacing receipt and journal printer.
• Fixing the problem in card reader either NON-ASD or ASD.
• Fixing problems in Cash dispenser /AFD/Presenter.
• Replacing LTI cover, replacing card reader head.
• Playing every day with Diebold Agilis software to troubleshoot and reset the module.
EDUCATION
• 10TH and 12th from Government Inter College Gadarpur Nainital with second division with P. C. M. group in 1991 and 1994.
PROFESSIONAL EDUCATION
• I am currently pursuing a B. Tech in Electronics Engineering from BITS Pilani, India.
• 3 years diploma in Electronics engineering specialization microprocessor from Government Polytechnic Mainpuri, UP, India. passed in 1999.
• One year certificate course in INDUSTRIAL ELECTRONICS from ATI-EPI Dehradun Uttarakhand, India. passed in April 2003
• 6TH month COMPUTER HARDWARE AND NETWORKING certificate course from
ESTC, Kania Ram Nagar Nainital, Uttarakhand, India. passed in March 2000.
• One year COMPUTER APPLICATION SOFTWARE course from CHANAKYA ACL Mainpuri, UP, India in January 1999.
Training
1-OHS General safety induction (CSCC00),
2-Basic fire fighting (CSCC24)
3-Hazard identification and risk assessment (CSCC01)
4-National grid electrical safe working procedures (CSCC08)
Personal Information
Nationality- Indian Driving License - India & Saudi Arab,
Language –Arabic, English, Urdu, Hindi, Basic German